Preformed Armor Rod-manufacture,factory,supplier from China

(Total 24 Products for Preformed Armor Rod)
The preformed armor rod is used to protect the wire from vibration, clamping stress, friction, arc and all other external damage. The armor rod section protection wire can protect the wire from arc, friction or other damage on the short-span line when the wire vibration is not serious.
  Contate agora
The protective armor rod is a metal wire that is spirally wound on the wire to increase the rigidity and vibration resistance of the wire at the winding position.
  Contate agora
The protective rod is divided into FYB and FYH types.
  Contate agora
The structure of the preformed armor rod and the short protective rod is simple. A set of pre-twisted wires form an empty tube, which generates a gripping force when wrapping the wire, thereby protecting the wire. The pre-twisted wire protection line is used for vibration protection and has been included in the hardware products.
  Contate agora
ADSS/OPGW anti-vibration hammer protective wire is a protective wire used to suppress the vibration of conductors and ground wires on overhead power lines.
  Contate agora
Stay rod is used for sustaining the mechanical load of the stay wires.The stay bow are made of Q235B steel, hot dip galvanized surface treatment which used for LV & MV stay rod assembly installation. Both bow type and tubular type we can supply, the tubular type stay rods MV & LV(M16×1830mm; M20×2440mm)exported to most of African countries.Features:1. Material: high strength carbon steel2. Application: for stay rod assembly3. Dimension: 16mm4. Finish: hot dip galvanized 
  Contate agora
The protective wire can avoid damage caused by the aluminum clamp of the anti-vibration hammer directly clamped on the 0PGW optical cable, and has a good protective effect on the optical cable. The factors that cause vibration include span, tension, wind speed, wind direction, ground wire and cable structure size, etc. Features: a. Using a unique design, its basic principle is to dynamically absorb energy, its frequency coverage is 6Hz-150Hz, and there are four resonance frequencies in this range, which can meet the needs of various types of OPGW, and has a very effective v
  Contate agora
The stay rods is for 40kN LV stays, the diameter of rods is M16, each element/material stay rod, stay base plate, guy grip, top make off, thimble are easy for assembly.A drawing of stay bows complete with thimble: 
  Contate agora
The stay rod is called stay set as well, it is a component used to connect the stay wire to the ground anchor.The stay rod are made of Q235B steel, hot dip galvanized surface treatment which used for LV & MV stay rod assembly installation. Both bow type and tubular type we can supply, the tubular type stay rods MV & LV(M16×1830mm; M20×2440mm)exported to most of African countries. Features:1. Material: high strength carbon steel2. Application: for stay rod assembly3. Dimension: M20×2440mm4. Finish: hot dip galvanized 
  Contate agora
The preformed top tie are all designed in a spiral structure and consist of two aluminum-clad steel wires. The central part of the power distribution cable is formed in the factory, and its shape can be matched with various insulators and wires.
  Contate agora
Stay guy grips are used for stay rod, stay insulator and pole top attachment.
  Contate agora
Power equipment optical cable communication 4D type protective hardware anti-vibration hammer with armor rod. Features: Due to the use of hammers with different sizes and masses, the response frequency range of traditional shock-proof hammers is expanded. Because the shapes of large and small hammers and hooks have no edges and corners, corona is reduced. In addition, the use of aluminum alloy for the hook can also reduce the energy loss of the wire.
  Contate agora
Tension insulators are used for transmission and distribution lines and communication lines, broadcast line terminals, corners or large-span poles, The balance pole is subjected to tensile stress. When in use, the wire and the pull wire pass through the hole and slot, and the tension wire is used for insulation and connection.Features:1. Material: high strength carbon steel2. Application: for stay rod assembly3. Dimension: M16×1830mm4. Finish: hot dip galvanized 
  Contate agora
The structure of the preformed strain clamp is straightforward, and its pre-twisted cord legs are twisted to form an empty tube, and the rear part is a pre-formed twisted ring. the empty tube shaped via the legs of the pre-twisted twine can generate a robust grip while it's far wound at the wire, and the twisted loop is used to restore the insulator.
  Contate agora
Product advantages: 1. There is a large contact area between the clamp and the pull wire, the stress distribution is even, there is no stress concentration point, and the achievable grip strength is not less than 95% of the stranded wire Calculate the breaking force. 2. The dead end preformed guy grip is made of the same material as the pull wire, which has good corrosion resistance. 3. The dead end preformed guy grip is simple to install, without any special tools, and can be done independently by one person.
  Contate agora
1.The preformed guy grip is used for the installation of ACSR conductors. The product is with much more reliability and economy compared with the bolt-type & hydraulic strain clamps.2. The structure of the preformed guy grip is simple. When installation, the tubular structure formed by the legs of the pre-twisted wire can be naturally wound on the conductor to produce a strong grip. The novel structure and unique design make the wire resistant to tension.
  Contate agora
1. The preformed guy grip is used for the installation of ACSR conductors. The product is with much more reliability and economy compared with the bolt-type & hydraulic strain clamps. 2. The structure of the preformed guy grip is simple. When installation, the tubular structure formed by the legs of the pre-twisted wire can be naturally wound on the conductor to produce a strong grip. The novel structure and unique design make the wire resistant to tension.
  Contate agora
Wire tension clamp NL-50/8 for steel core aluminum stranded wire made of galvanized steel wire or alloy clad steel wire. 1. The preformed guy grip is used for the installation of ACSR conductors. The product is with much more reliability and economy compared with the bolt-type & hydraulic strain clamps. 2. The structure of the preformed guy grip is simple. When installation, the tubular structure formed by the legs of the pre-twisted wire can be naturally wound on the conductor to produce a strong grip.
  Contate agora
The stay plates are made of Q235B steel, hot dip galvanized surface treatment which used for LV & MV stay rod assembly installation. Both bow type and tubular type we can supply, the tubular type stay rods MV & LV(M16×1830mm; M20×2440mm)exported to most of African countries.Features:1. Material: high strength carbon steel2. Application: for stay rod assembly3. Dimension: 450×450×6mm×22mm hole diameter4. Finish: hot dip galvanized 
  Contate agora
The power distribution top tie can be used to fix bare or insulated wires in the top grooves of pin insulators and post insulators of the power distribution system.
  Contate agora
The preformed strain clamp is used to bear full tension on the bare conductors and overhead insulated conductors in the power transmission and distribution line, and connect the conductors to the strain tower, which can replace the conventional bolt-type strain clamp and compression type strain Clamps and wedge-shaped strain clamps.Structure composition and material description 1. Non-twisted ring: standard form, suitable for small diameter wires; Stranded ring: suitable for larger diameter wires 2. Color code: starting mark of installation 3. Label: Indicate the
  Contate agora
Fiber optic tangent used as cable suspension hardware first-rate at the identical time because the attitude of alternate, each horizontal or vertical, is a good deal much less then 15°.Armor grip suspesnion used for any span duration with an perspective change, each horizontal or vertical, a whole lot much less than 30°.There are 3 types of ADSS fitting suspension grips: 1. ADSS fitting for span length less than 70msuspension with suspention rods and  protection rods,  ring type thimble and pole attachment, steel tip, D shackle with related accessories. 2.
  Contate agora
Stay grips dead ends is the preformed wire type, minimum length is 600mm and finish is galvanized. Thimbles is used with guy grips to support wires through the stay rod eye. A combination of guy grips and pole top make offs is used.Installation image:
  Contate agora
The aluminum terminal is pressed by aluminum rod, and made of punching press. It is used for the connection of distribution box, aluminum wire, aluminum cable and other wires. It is preferably pure aluminum, which has good electrical conductivity, high temperature resistance, fast heat dissipation, galvanic corrosion resistance, and long service life.
  Contate agora
Relate News
Characteristics1) low wear: because of the big bar and short good sized clench conductor, the cord is tough to slide, the wear and tear might be minimum.2) save you loosening: the preformed has preserving elasticity, it make sure it not unfastened in long time;3) good corrosion-resistance characteristics: after antirust processing, the cord ensuring the sturdy corrosion resistance;4) clean set up: no unique equipment, the hand can installation quick and easy in locale, one person can finish.5) installation first-class warranty: no need the special training; it is able to be inspected by using
Spiral preformed tension clamp and ADSS single-layer tension clamp have similar functions as tension clamp. Spiral preformed tension clamps are mainly used for poles and towers with short spans of 50 to 200 meters, such as corners, tensions, and terminals.
The preformed suspension clamp is used for the connection of various wires such as ADSS optical cable and OPGW optical cable in the linear pole tower.
The tension clamp is deployed at a ordinary time. the current within the circuit is deployed from one end of the electricity supply, and the electrical putting gadget is deployed returned to the opposite end of the strength supply to form a closed circuit. if the present day circuit is blocked, the disconnection may arise due to some purpose. the modern-day within the circuit is not smooth, and the circuit does no longer form a closed loop. this is called an open circuit. therefore, all components need to be freed from hysteresis loss.
We clean our workshop on time and keep our workers workings in a clean, comfortable and organized place. 
We finished the HDG angle cross arm and arranged shipment in May of 2019 to our customers from Tanzania. 
After finishing products, before packing, we put our products in very tidy way so that the quantity never be shortage when customers received the items. 
Characteristics of PET Packing Tape(1) Sturdy tensile energy, not most effective has the tensile power of metal strip, but additionally has the ductility of effect resistance, that may ensure the transportation safety of merchandise. (2) Small elongation, elongation is most effective one-sixth of the polypropylene belt, can hold the anxiety for a long time. (3)Robust temperature resistance, melting point of 260 stages, a hundred and twenty degrees under the use of non-deformation. (4) Top security, no metal rust pollutants of the sure gadgets, vivid shade can be used for referen
Power fittings are accessories made of metal materials that are often used for power output. These accessories are of various types, and the shape and size of each part are different, but they play a very important role. Even very small parts will be indispensable, helping people to output electricity. Some of our common metal rings or metal clips, as well as connecting rings that can be connected to metal pipes, belong to the category of fittings.
Wonderful anti-pressure ability, accurate brief-circuit current ability ;Match with ordinary floor cord l undertake stainless-steel pipe production generation, the pipe is full of water-blocking off compounds, the application version can efficaciously protect the optical fiber ;Using stainless steel tube production technology, the tube filled with water-blocking compounds, can effectively protect the optical fiber;The utility model has the dual functions of a ground wire and a communication optical cable, and avoids the huge cost of repeated erection and maintenance;It is installed on the top
The hoop is used to restore the metal strand or cord on the pole, and the pull is much like solving to the wall or other objects to tighten the steel strand. There are numerous styles of hoops, cable hoops, telegraph pole hoops, cable hoops, cable hoops, and stainless-steel hoops are extra usually used.Cement poles can be divided into rectangular, octagonal, i-formed, circular or a few different particular-common go-section poles in step with their cross-sections. amongst them, the extra generally used are spherical bolstered concrete poles.
We sent our bolts samples to the National space frame and steel structure quality supervision and inspection center, the samples were tested and meet the technical requirements of standard GB/T 2694-2010 and GB/T 3098.1-2010.