PARALLEL GROOVE CLAMPS-manufacture,factory,supplier from China

JBL series special-shaped parallel groove clamps are used for the connection of small and medium cross-section aluminum stranded wire or steel core aluminum stranded wire and the steel stranded wire of overhead lightning protection wire at a position that does not bear tension.

APG-A1 Aluminum Parallel M&A Clamp is suitable for the non-load-bearing splicing and branching of aluminum stranded wires and steel core aluminum stranded wires.

Features:1. Material: aluminum alloy2. Teeth shape, with low resistance, reliable splicing.3. All parts connected completely, can’t lose any one during installation.4. arc hold mostly tightly, conductor can’t be moved. 

There are many types of products with complete models.Hot-dip galvanized bolts, has strong corrosion resistance.Complying International standard, ensure quality.Model No.: P-7Tension strength: 70KNThe main dimensions of the Parallel hanging clevis meets the requirements of the following figure and table:The meanings of letters and numbers in the models in the table are: number--nominal failure load mark.

Bimetal PG clamp is used in non-strain tapping or connecting to a line suitable for aluminium and copper conductors.Features:M12 bolts and nuts and washers : mild steelFinish: tin platedMinimum ampere rating: 300ATypeConductor mm²JBTL 16-12016-120JBTL 50-24050-240

J bolts is supplied with one full nut and round washer. The material of the bolts is steel, strength grade designation 4.6. Screw threads is parallel throughout their length. After galvanizing, the nut can be easily screwed by hand over the whole threaded length. 

The grounding clamp is mainly used for the grounding of the OPGW optical cable to provide a path for short-circuit current. The grounding clamp consists of a grounding wire, a set of aluminum alloy parallel groove clamps (connecting OPGW optical cable and grounding wire) and a terminal (connecting to the iron tower). Usually, one terminal tower and linear tower are equipped, and two connecting towers are equipped.

The multipurpose pole clamp is fabricated from structural steel grade 235 and is hot dipped galvanized. The tensile strength of the multipurpose pole clamp is not less than 70KN for the light duty clamps and 120KN for the heavy duty clamps respectively. The clamps is supplied complete with bolts, locking nut, flat washer and spring washer for main or rib line.Cutting and surface1. The cutting is by cold process while bending and shaping is by hot forging. It is capable of being re-flattened without fracture.

The hook of the parallel cable clamp can be rotated and fixed at ninety degrees. It is used to fix the optical cable wire, fasten it on the steel strand, and connect and fix the S-shaped fixing member on the steel strand.  The stranded stay wire is 2.0mm*7 & 2.2mm*7.Dimension : 50×31.5×80mm（L×W×H)Installation image: Drawing: 

Suspension clamps for optical cables are made of real materials, with stable performance and long service life. Composed of insulating clamps and connecting buckles, the stress distribution is even, there is no concentrated point, it can enhance the rigidity of the cable installation point, and the protection performance of the optical cable is good. It has a larger contact area with the optical cable and is equipped with flexible rubber clamps to enhance self-damping and reduce wear.

ADSS optical cable small pitch suspension clamps are mainly used for cable erection within 100m pitch, and single-layer pre-twisted wire suspension clamps are mainly used for optical cable erection within 100m~200m pitch.

The pole hoop has various dimension of 50mm 65mm 75mm 80mm 100mm 130mm 150mm 200mm 250mm 300mm 350mm 400mm 500mm. Semi-circular cable hoop used in high-altitude suspension, hardware fasteners, the product is waterproof and rust-proof. It is used in complex and harsh environments, and the effect is good. Features: 1.

Pigtail Bolt M16 used on wooden, concrete and other power poles for supporting clamps and at the consumer’s premises. The clamps corrosion resistance conforms to the standards.Bolts and nuts is made of hot dip galvanised steel. Ultimate Tensile strength (UTS) of the clamp is 20KN.

The JJC series of low-voltage cable piercing clamps use excellent insulation materials and sufficient materials, which greatly improves the stability of the product and has a long service life. The product models are complete in variety, stable in size and easy to match.

The pole hoop is used to connect the tension suspension clamp and the electric pole.The cable hoop is a cable in the line to fix the pole. There are flat hoop, reinforced flat hoop, double hoop hoop and four hoop hoop. Generally, the specifications of flat steel and the diameter of the rods to be held are used to express its specifications, such as 60×6×150. Features: 1.

ADSS optical cable suspension clamps are divided into several types according to the size of the line span, such as single-layer pre-twisted wire tangent clamps, single suspension clamps and double suspension clamps. The tangent clamp for ADSS optical cable is mainly used for the cable erection of 100m span, and the single-layer pre-twisted wire suspension clamp is mainly used for the erection of optical cable within the span of 100m-200m.Features: a. The suspension clamp has a larger contact area with the ADSS/OPGW optical cable, the stress is evenly distributed, and there is n

CAPG copper-aluminum special-shaped parallel clamp is suitable for the non-load-bearing splicing and branching of aluminum stranded wire, steel core aluminum stranded wire and copper branch wire. Through the re-processing of the profile, the aluminum density is better after the second forging, and the strength of the wire clip is improved. higher. There is a layer of blue epoxy resin on the inside of the wire clip to better isolate the air from the copper-aluminum welding joint and prevent the electrochemical corrosion of the copper-aluminum.

The fastening clamps for ADSS optical cable towers are divided into straight-line fastening clamps for towers and tensile fastening clamps for towers.Straight ADSS tower Tension splint is made of hot dip galvanized steel.use: Connection of strain clamps, suspension clamps, remaining cable racks and optical cable connection boxes to the iron tower.Technical Parameters: Damage load (kN) and the size of the main material of the power tower at the location of the optical cable hanging point.Configuration method: It can be used in one-to-one correspondence with strain clamps, suspension clamps

Down-lead clamps for rubber towers are used to fix the up and down or up of the optical cable on the tower so that it will not shake and avoid the optical cable from wearing. Features: 1.Wide range of application: It is suitable for skeleton type, layer stranded type, beam tube type armored and non-armored fiber optic cables, and is flexible in use. 2.

Storage kit made of same material as the universal pole clamps(hot dip galvanized steel Q235B) and fabricated in the form of a cross arm and provided with suitable method to affix on the pole.

The JJC series of low-voltage cable piercing clamps use excellent insulation materials and sufficient materials, which greatly improves the stability of the product and has a long service life. The product models are complete in variety, stable in size and easy to match. It is used for the branch connection of insulated cables in building power distribution systems, the connection of low-voltage overhead insulated cables, the branch connection of low-voltage insulated incoming cables, and the street lamp power distribution system. Features:1. Main branch： 1.5-25sqmm2.

Tangent clamp for ADSS diameter 11-12mm span 100m galvanized steel and neoprene protection, anti-UV resistant, max cable angle 20 degrees.This product is a single hanging point for overhead lines, single hanging, no internal and external pre-twisted wire clamps, this product plays a fixed and traction role, can simply adapt to the problem of unbalanced forces on both sides, and can more effectively adapt to both sides Torque and moment problems caused by different pulling forces.This product has rubber clamps and one-piece aluminum alloy casing (butterfly type).

The S type cable clamp is used to bind the self-supporting leather cable suspension wire and hang the optical cable on the supporting device, be steadily strengthened and tightened. There are several colors can be chosen: gray, black, white.Instruction： Wrap the 2-5mm optical brazing wire in the cylindrical groove of the S part, and fix the optical brazing wire connecting rod.Packing: comes in plastic first then put in strong durable cardboard box with labels stick on the outer package. Installation image: 

The S drop cable clamp is made of stainless steel rope and flame-retardant ABS plastic body, one head with a round steel wire, used to bind the self-supporting drop cable suspension wire, and hang the optical cable on the supporting device.Dimension：135×23.5×17.5mm（L×W×H).Instruction： Wrap the 2-6mm optical brazing wire in the cylindrical groove of the S part, and fix the optical brazing wire connecting rod.Packing： plastic bag first then come in a resistant biodegradable cardboard box with the customer information in the visible part of the box. Installation image: