LV Stay Assembly 11KV-manufacture,factory,supplier from China

(Total 24 Products for LV Stay Assembly 11KV)
The stay rods is for 40kN LV stays, the diameter of rods is M16, each element/material stay rod, stay base plate, guy grip, top make off, thimble are easy for assembly.A drawing of stay bows complete with thimble: 
  Contate agora
Stay rod is used for sustaining the mechanical load of the stay wires.The stay bow are made of Q235B steel, hot dip galvanized surface treatment which used for LV & MV stay rod assembly installation. Both bow type and tubular type we can supply, the tubular type stay rods MV & LV(M16×1830mm; M20×2440mm)exported to most of African countries.Features:1. Material: high strength carbon steel2. Application: for stay rod assembly3. Dimension: 16mm4. Finish: hot dip galvanized 
  Contate agora
The stay plates are made of Q235B steel, hot dip galvanized surface treatment which used for LV & MV stay rod assembly installation. Both bow type and tubular type we can supply, the tubular type stay rods MV & LV(M16×1830mm; M20×2440mm)exported to most of African countries.Features:1. Material: high strength carbon steel2. Application: for stay rod assembly3. Dimension: 450×450×6mm×22mm hole diameter4. Finish: hot dip galvanized 
  Contate agora
The stay rod is called stay set as well, it is a component used to connect the stay wire to the ground anchor.The stay rod are made of Q235B steel, hot dip galvanized surface treatment which used for LV & MV stay rod assembly installation. Both bow type and tubular type we can supply, the tubular type stay rods MV & LV(M16×1830mm; M20×2440mm)exported to most of African countries. Features:1. Material: high strength carbon steel2. Application: for stay rod assembly3. Dimension: M20×2440mm4. Finish: hot dip galvanized 
  Contate agora
Tension insulators are used for transmission and distribution lines and communication lines, broadcast line terminals, corners or large-span poles, The balance pole is subjected to tensile stress. When in use, the wire and the pull wire pass through the hole and slot, and the tension wire is used for insulation and connection.Features:1. Material: high strength carbon steel2. Application: for stay rod assembly3. Dimension: M16×1830mm4. Finish: hot dip galvanized 
  Contate agora
Stay guy grips are used for stay rod, stay insulator and pole top attachment.
  Contate agora
The tie strap is used for tying 11kV or 33kV cross-arms to poles. There are steel galvanized bolts and nuts assembled.  All ferrous part is made in hot dip galvanized.
  Contate agora
Stay grips dead ends is the preformed wire type, minimum length is 600mm and finish is galvanized. Thimbles is used with guy grips to support wires through the stay rod eye. A combination of guy grips and pole top make offs is used.Installation image:
  Contate agora
Galvanized steel pole top make off is generally double wrapped around the pole. 3 strands plus king wire and effective 7 strand stay length for dead end attachment.  top to facilitate termination of the stay strand that firms the pole on the earth.Features:1. Material: galvanized steel wire2. Application: for stay rod assembly3. Dimension: 1750 overall length mm4. Finish: hot dip galvanized5. Stay wire diameter: 12mm6. Tensile strength” 63kNProduction drawing: Installation image: 
  Contate agora
The second damper can be used for OPGW tension tower vibration dampers if necessary. Tension assembly is used for OPGW cable route's fixing and anchor shackling. Usually be installed on the terminal tower, tight tension tower and intersection angle tower.OPGW tension tower vibration dampers installation image: 
  Contate agora
The galvanized steel strand is made of galvanized material and is composed of multiple steel wires. It has strong anti-rust, anti-rust ability, corrosion resistance, strong load-bearing, and good toughness. After multiple tensile tests, each steel wire rope has no breaks and no loose strands. The surface is smooth, burr-free, high tensile strength, and small bending radius.
  Contate agora
Features: 1. The application force has no concentrated point, the stress is uniform, and it has a good protective effect on the optical cable. 2. Under the premise of not exceeding the lateral compression strength of the optical cable, it has a greater grip on the optical cable and can withstand greater tension.
  Contate agora
The hook of the parallel cable clamp can be rotated and fixed at ninety degrees. It is used to fix the optical cable wire, fasten it on the steel strand, and connect and fix the S-shaped fixing member on the steel strand.  The stranded stay wire is 2.0mm*7 & 2.2mm*7.Dimension : 50×31.5×80mm(L×W×H)Installation image: Drawing: 
  Contate agora
Tension set ADSS cables installation requires a special tangent assembly or a mechanical dead end at each pole. Tension clamp helical spiral usually with several numbers of rods, such as 7 of rods and thickness of each rod can be different based on different requirements. 2.5mm is the most often cable sizes. And always be compatible with fitting accessories.Sn Model No.
  Contate agora
A hoop is a component that uses one material to hug or hoop another material, which is a fastener. There are many types of hoops, cable hoops, telegraph pole hoops, cable hoops, cable hoops, and stainless steel hoops are more commonly used.Technical specification table: 
  Contate agora
The preformed dead end is used to fix the cable clamp of the cable of the tower, the iron tower, and the microwave tower. It can replace the U-T clamp and the wedge clamp that are commonly used to fix the cable on the line tower. The unique design makes the tension-resistant structure of the cable simple and reliable. After installation, the empty tube formed by the twisting of the two legs of the pre-twisted wire of the wire clip can be wound on the cable to produce a strong grip. The twisted ring is used to fix the ground anchor. Or on the tower pole.
  Contate agora
1. The twisting direction of the steel stranded wire and the matching preformed guy grip needs to be the same, and the tensile strength of the galvanized steel wire is 1370N/mm2-1470N/mm2. 2. The white corundum used to increase the friction between the pre-twisted wire and the surface should meet the requirements of GB/T 2479.3. The surface of the preformed guy grip should be smooth and free of defects such as cracks, folds and scars.4. The size and tolerance of the pre-twisted wire The size of the pre-twisted wire should meet the requirements of the design d
  Contate agora
According to the size of the object to be bound, it can be cut to any desired length, equipped with stainless steel buckles, and quickly installed with the corresponding strap tightening machine, which is safe, fast and reliable.Material: cast steelSuitable for width of band strap: 9.5-25.0mm Suitable for thickness of band strap: 0.8-1.0mmSurface treatment: sprayed, chrome platedOur tension tool for SS strapping band with the advantages below: 1.It has a wide range of applications and multiple uses.
  Contate agora
Tie rods is supplied with four full nuts. The material of the rods is steel, strength grade designation 4.6 and meet the requirements for mechanical properties.
  Contate agora
The repair sleeve comprises of two pieces with a provision of seat for sliding of the keeper piece.
  Contate agora
Steel belt 20X0.7mm with buckle, tts strength and ductility meet requirements for bending the different size of cables on poles. Steel Buckle can hold a single or double wrapped band configuration.Packing:Steel roll of 50 m is packed in form of closed reel rewind tape in nylon plastic roll.
  Contate agora
Drop cable pole fasten clamp is a one-piece design that combines the traditional accessory accessories, and also forms multiple anchor nodes on the wire rod. The small size can be used for 90-140mm poles, and the medium size can be used for 135-230mm poles.CompositionFor pole 80-140mm 100 pieces per Carton Plywood pallet
  Contate agora
Down-lead clamps for rubber towers are used to fix the up and down or up of the optical cable on the tower so that it will not shake and avoid the optical cable from wearing. Features: 1.Wide range of application: It is suitable for skeleton type, layer stranded type, beam tube type armored and non-armored fiber optic cables, and is flexible in use. 2.
  Contate agora
The down-lead clamp for metal rods is used to fix ADSS on the rod. It is suitable for different cable diameters. It is convenient and reliable to install and has a wide adjustable range.1.Function: Fix the optical cable leading up or down on the pole tower to prevent it from shaking and avoid the optical cable from wearing. 2.Condition: The fiber optic cable line and the continuous poles on the first and end poles. 3.Method: usually install one every 1.5 meters.Technical specification table: 
  Contate agora
Relate News
Wonderful anti-pressure ability, accurate brief-circuit current ability ;Match with ordinary floor cord l undertake stainless-steel pipe production generation, the pipe is full of water-blocking off compounds, the application version can efficaciously protect the optical fiber ;Using stainless steel tube production technology, the tube filled with water-blocking compounds, can effectively protect the optical fiber;The utility model has the dual functions of a ground wire and a communication optical cable, and avoids the huge cost of repeated erection and maintenance;It is installed on the top
The tension clamp is deployed at a ordinary time. the current within the circuit is deployed from one end of the electricity supply, and the electrical putting gadget is deployed returned to the opposite end of the strength supply to form a closed circuit. if the present day circuit is blocked, the disconnection may arise due to some purpose. the modern-day within the circuit is not smooth, and the circuit does no longer form a closed loop. this is called an open circuit. therefore, all components need to be freed from hysteresis loss.
After finishing products, before packing, we put our products in very tidy way so that the quantity never be shortage when customers received the items. 
We clean our workshop on time and keep our workers workings in a clean, comfortable and organized place. 
Power fittings are accessories made of metal materials that are often used for power output. These accessories are of various types, and the shape and size of each part are different, but they play a very important role. Even very small parts will be indispensable, helping people to output electricity. Some of our common metal rings or metal clips, as well as connecting rings that can be connected to metal pipes, belong to the category of fittings.
Characteristics of PET Packing Tape(1) Sturdy tensile energy, not most effective has the tensile power of metal strip, but additionally has the ductility of effect resistance, that may ensure the transportation safety of merchandise. (2) Small elongation, elongation is most effective one-sixth of the polypropylene belt, can hold the anxiety for a long time. (3)Robust temperature resistance, melting point of 260 stages, a hundred and twenty degrees under the use of non-deformation. (4) Top security, no metal rust pollutants of the sure gadgets, vivid shade can be used for referen
We finished the HDG angle cross arm and arranged shipment in May of 2019 to our customers from Tanzania. 
The standard plywood crates customized based on requirements of customers and loaded in the container.
The hoop is used to restore the metal strand or cord on the pole, and the pull is much like solving to the wall or other objects to tighten the steel strand. There are numerous styles of hoops, cable hoops, telegraph pole hoops, cable hoops, cable hoops, and stainless-steel hoops are extra usually used.Cement poles can be divided into rectangular, octagonal, i-formed, circular or a few different particular-common go-section poles in step with their cross-sections. amongst them, the extra generally used are spherical bolstered concrete poles.
We sent our bolts samples to the National space frame and steel structure quality supervision and inspection center, the samples were tested and meet the technical requirements of standard GB/T 2694-2010 and GB/T 3098.1-2010. 
Optical cable joint box, ADSS optical cable joint box, OPGW optical cable joint box, OPPC optical cable joint box Uses: Widely used in ADSS, OPGW special optical cable joints and the junction of different optical cables, and play a role in protecting optical cable joints. Features: 1.The metal splice box is made of aluminum alloy casting, which is especially suitable for the protection of optical cable joints under high-voltage electric fields. 2.The metal splice box overcomes the weakness of the plastic splice box, which is poor in anti-aging ability and short life under t
With the continuous growth of China's national economy as a whole and the influence of the reform of telecommunications system, the market demand for ADSS power optical cable has increased significantly, reaching 10 million core kilometers in 2001.In the 21st century, there were several situations at that time: (1) Domestic optical cable enterprises were affected by the "bubble" of optical network, and the telecom market shrank, and the supply exceeded demand.