Doan Lead Clamp-manufacture,factory,supplier from China

ADSS optical cable tower with down-lead clamp, optical cable clamp, fixed optical cable clamp.The lead-down clamp is used to lead down the optical cable and fix the optical cable when it is jumpered, which improves the mechanical performance of the clamp. It is mainly used for the communication line of the newly built overhead high-voltage power transmission system of 35kv and above. The stainless steel tube and cable core stranding design is reasonable, and the optical fiber is redundant.

Down-lead clamps for rubber towers are used to fix the up and down or up of the optical cable on the tower so that it will not shake and avoid the optical cable from wearing. Features: 1.Wide range of application: It is suitable for skeleton type, layer stranded type, beam tube type armored and non-armored fiber optic cables, and is flexible in use. 2.

The turnbuckle bolts are expanded and contracted by the lead screw, which can adjust the tightness of the wire rope. The components can be bundled during component transportation and loosened during installation and correction.1.Types: turnbuckle bolt, open body turnbuckle2.Material: Q235B steel  3.The main purpose:  to adjust the tightness of the wire rope, and it is widely used.4.Features: simple structure, easy processing, low cost, and strong practicability.

The down-lead clamp for metal rods is used to fix ADSS on the rod. It is suitable for different cable diameters. It is convenient and reliable to install and has a wide adjustable range.1.Function: Fix the optical cable leading up or down on the pole tower to prevent it from shaking and avoid the optical cable from wearing. 2.Condition: The fiber optic cable line and the continuous poles on the first and end poles. 3.Method: usually install one every 1.5 meters.Technical specification table: 

ADSS optical cable rubber rod down-lead clamp is made of corrosion-resistant, weather-resistant EPDM rubber. It is used for fixing ADSS on the pole tower, suitable for different cable diameters, convenient and reliable installation, and wide adjustable range.1.Function: Fix the optical cable leading up or down on the pole tower to prevent it from shaking and avoid the optical cable from wearing. 2.Condition: The fiber optic cable line and the continuous poles on the first and end poles. 3.Method: usually install one every 1.5 meters.Technical specification table: 

The wire rope clamp is corrosion-resistant, not easy to rust, and has the strength of the wire rope. It is safe to use, beautiful in appearance and smooth in transition. The lifting operation has a large safe load, can resist impact load and has a long service life.

• The elasticity of the C-shaped element can maintain a constant contact pressure between the wire and the clamp for a long time, a constant and sufficiently large contact pressure, and the maximized contact surface can maintain a very low contact resistance for a long time.•Unique structure to ensure that the pressure of the wires (different wire diameters) on both sides is equalized, and the large and small wires are skipped.• Long-term stable and good contact performance: maintenance-free, maintenance-free, reducing maintenance costs.•Scientific and advanced articulated structure, which sav

The wire clamp is composed of a rubber clamp block, a pre-twisted wire and a cast aluminum casing. 1. Enhance the rigidity of the cable hanging point and increase the radius of curvature. The single-line clamp can meet the 30° steering angle, and the double-line clamp can meet the 60° steering angle. 2. It can be ensured that the cable is not subject to large bending stress near the outlet of the wire clamp, so as to avoid local mechanical damage causing strand break or wire breakage.

ODWAC, FTTH Self-supporting butterfly-shaped lead-in optical fiber cable installation accessories, stainless steel clamps, optical cable fixing partsThe fiber is squeezed through the sheet and the sheet, and the fiber is squeezed in the middle to complete the wiring function. The main function is to prevent the wire body from bending and protect the wire body, and the locking position can be moved quickly and simply. It is easy to use, put the optical fiber into the slot, install the pull piece, and tighten it.For self-riding butterfly optical cable 2*6mmBreaking load: 1 kNInstallati

Bimetal PG clamp is used in non-strain tapping or connecting to a line suitable for aluminium and copper conductors.Features:M12 bolts and nuts and washers : mild steelFinish: tin platedMinimum ampere rating: 300ATypeConductor mm²JBTL 16-12016-120JBTL 50-24050-240

The suspension support hook clamp made of hot dip galvanized steel, the dimension is 120mm （L）and 10mm as diameter of the hook. There is one hole of M14 punched on the base plate. The thickness of the base plate is 3.2mm. 

Features: 1. It has all the functions of a single suspension clamp.2.

Dead end clamp is made of plastic body with very high mechanical and climatic resistance. A stainless steel flexible cord equipped with movable insulating saddle and two sleeves compressed on the ends to prevent detachment from the clamp body.An inner sheath consisting of two insulating plastic wedges for clamping of the neutral carrier without damaging the cable insulation.

Eye to eye turnbuckle is composed of an adjusting rod with left and right threads, a nut and a tie rod. It uses a lead screw to expand and contract to adjust the tightness of the wire rope. In order to prevent rust, the surface treatment of turnbuckle screws: generally electroplating and hot-dip plating.1.Types: turnbuckle bolt, open body turnbuckle2.Material: Q235B steel  3.The main purpose:  to adjust the tightness of the wire rope, and it is widely used.4.Features: simple structure, easy processing, low cost, and strong practicability.

The structure of the preformed strain clamp is straightforward, and its pre-twisted cord legs are twisted to form an empty tube, and the rear part is a pre-formed twisted ring. the empty tube shaped via the legs of the pre-twisted twine can generate a robust grip while it's far wound at the wire, and the twisted loop is used to restore the insulator.

Self-supporting optical cable clamp ADSS optical cable tension clamp is a commonly used ADSS optical cable clamp. The main body material is PA66, stainless steel wire rope, injection molding process, widely used in communication engineering, etc. Mainly used for optical cables with 8-12mm cable diameter. Large quantities are exported to South America, Southeast Asia and other countries and regions.Features:Dimension: 205×90×45mmUnit weight:410gCarton size: 550×410×250mmQuantity per carton : 50 piecesMaterial: Nylon and stainless steelCable diameter: 8-12mmInstallation image: 

The JJC series of low-voltage cable piercing clamps use excellent insulation materials and sufficient materials, which greatly improves the stability of the product and has a long service life. The product models are complete in variety, stable in size and easy to match.

APG-A1 Aluminum Parallel M&A Clamp is suitable for the non-load-bearing splicing and branching of aluminum stranded wires and steel core aluminum stranded wires.

The self-supporting fiber optic cable clamp ADSS fiber optic cable tension clamp produced by our company, the specification is 5-8mm, is widely used in various optical fiber communication and network projects. Stainless steel wire rope and PA66 main material, injection molding process, color is black. It has the advantages of convenient use, firm fixation, and reduced working hours.

CAPG copper-aluminum special-shaped parallel clamp is suitable for the non-load-bearing splicing and branching of aluminum stranded wire, steel core aluminum stranded wire and copper branch wire. Through the re-processing of the profile, the aluminum density is better after the second forging, and the strength of the wire clip is improved. higher. There is a layer of blue epoxy resin on the inside of the wire clip to better isolate the air from the copper-aluminum welding joint and prevent the electrochemical corrosion of the copper-aluminum.

The mounting hook clamp are used on poles such as telegraph poles or cylindrical poles. The main purpose is to form an anchor point and erect an optical fiber line body. The finish is hot-dip galvanized, which is corrosion-resistant and anti-rust. The two sides are transparent, equipped with stainless steel fastening strips, which are firm, stable and beautiful after installation.Usage: Used with 12-20mm steel belt, fixed on the pole.Material: carbon steelDimension：65×65×54mm（L×W×H).Installation image: 

FTTH fiber-in-the-home clamp, designed for hanging, flat optical cable. The clamp is very easy to install and does not require other tools. It can be easily installed on the hanging bracket by manually adjusting the hanging ring. The clamp is equipped with perforated gaskets, which can increase the load when the optical cable is dropped.

The self-supporting figure 8 optical cable clamp has a flat surface, special material and embedded design, which can well protect the cable. Its technology is superb: high-quality aluminum alloy material, rubber clamp block, reduce wear.

Our clamp tool for SS banding strap with the advantages below: 1.It has a wide range of applications and multiple uses. It can be used to bundle cables, pipes, signs, brackets, etc. 2.As a packing tool, it saves time and effort, is convenient to tighten, the card slot is fixed, and it is easy to cut. 3.Comfortable handle, easy to operate, thick plastic powder, wear-resistant, suitable for complex operating environment. 4.Die design, sturdy and durable. Forged with high-strength tool steel, strong and durable. 5.Simple operation and convenient installation.